Scanner block
Example of Load Switch Circuit for ON/OFF Control of LEDs for Scanner Light Source
Lineup
Small signal MOSFET
| Part number | SSM3K35FS | SSM3K35AFS | SSM3J35FS | SSM3J35AFS | |
|---|---|---|---|---|---|
| Package | SSM | SSM | SSM | SSM | |
| VDSS [V] | 20 | 20 | -20 | -20 | |
| ID [A] | 0.18 | 0.25 | -0.1 | -0.25 | |
RDS(ON)[Ω] @|VGS|=2.5 V |
Typ. | 2 | 1.1 | 5.6 | 1.5 |
| Max | 4 | 1.6 | 11 | 2.1 | |
| Polarity | N-ch | N-ch | P-ch |
P-ch | |
MCU (TXZ+TM3A Series M3H Group / TX04 Series M460 Group / TXZ+TM4A Series M4G / M4N Group)
| Series | Group | Function |
|---|---|---|
| TXZ+™3A Series | M3H Group | Arm® Cortex®-M3, 120 MHz operation frequency (Max). |
| TX04 Series | M460 Group | Arm® Cortex®-M4, 120 MHz operation frequency (Max). |
| TXZ+™4A Series | M4G / M4N Group | Arm® Cortex®-M4, 200 MHz operation frequency (Max). |
Stepping motor driver built-in AGC
| Part number | TB67S128FTG | TB67S289FTG | |
|---|---|---|---|
| Absolute Maximum Ratings | Output voltage | 50 V | |
| Output current | 5.0 A | 3.0 A | |
| On-resistance (H+L) | 0.25 Ω (Typ.) | 0.4 Ω (Typ.) | |
| Control interface | Clock / serial | Clock input | |
| Step | 1/1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64 | 1/1, 1/2, 1/4, 1/8, 1/16, 1/32 | |
| Features | ADMD (high efficiency control at high speed rotation) ACDS (built-in sense resistor less current control architecture) |
||
| Error detection function | TSD, ISD, POR, OPD | ||
| Package | VQFN64 | VQFN48 | |
Linear image sensor (CCD)
| Part Number | TCD2569BFG |
|---|---|
| Pixel Size | 5.25 μm by 5.25 μm |
| Line Spacing (Line Distance) | 2 line spacing (10.5 μm) |
| Effective Pixel Number | 5340 pixels by 3 lines |
| Sensitivity (A light source + CM500S) (Typ.) | Red: 13.2 V/(lx·s); Green: 15.0 V/(lx·s); Blue: 5.9 V/(lx·s) |
| Maximum Clock Pulse Frequency | 35 MHz |
| Power Supply Voltage (Operating Range) | 9.5 to 10.5 V |
| Maximum Output Voltage (Max) | 1.8 V |
| Saturation Output Voltage of CCD Shift Register (Min) | 4.0 V |
| Features | Sample and Hold Circuit; Clipping Function; Clamp Circuit |
| Part Number | TCD2726DG | |
|---|---|---|
| Pixel Size | 4.7 μm by 4.7 μm | |
| Line Spacing (Line Distance) | 2 line spacing (9.4 μm) | |
| Effective Pixel Number | 7500 pixels by 3 lines | |
| Sensitivity (A light source + CM500S) (Typ.) | Red: 11.1 V/(lx·s); Green: 14.9 V/(lx·s); Blue: 5.2 V/(lx·s) | |
| Maximum Clock Pulse Frequency | 100 MHz (50 MHz × 2 ch) | |
Power Supply Voltage (Operating Range) |
3.3 V (Digital) | 3.1 to 3.5 V |
| 3.3 V (Analog) | 3.1 to 3.5 V | |
| 10 V | 9.5 to 10.5 V | |
| Features | Timing Generator circuit, CCD driver | |
* Arm and Cortex are registered trademarks of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
* TXZ+™ is a trademark of Toshiba Electronic Devices & Storage Corporation.
A new window will open