Part Number Search

Cross Reference Search

About information presented in this cross reference

The information presented in this cross reference is based on TOSHIBA's selection criteria and should be treated as a suggestion only. Please carefully review the latest versions of all relevant information on the TOSHIBA products, including without limitation data sheets and validate all operating parameters of the TOSHIBA products to ensure that the suggested TOSHIBA products are truly compatible with your design and application.
Please note that this cross reference is based on TOSHIBA's estimate of compatibility with other manufacturers' products, based on other manufacturers' published data, at the time the data was collected.
TOSHIBA is not responsible for any incorrect or incomplete information. Information is subject to change at any time without notice.

Keyword Search

Parametric Search

Stock Check & Purchase

Select Product Categories

TLCS-870/C1 Series

A sample program is available for each product in the following configuration.

TLCS-870/C1 Series

TMP89Fx : TMP89FM42V / TMP89FS60V / TMP89FS62V / TMP89FS63V
TMP89FWy : TMP89FW20V / TMP89FW24V

Function Description Product Name
TMP89
Fx
TMP89
FWy
10-bit AD Converter ADC
REPEAT
The analog input value is AD-converted 10 times, and the average result is displayed on a terminal emulator. V V
ADC
SINGLE
The analog input value is AD-converted once, and the result is displayed on a terminal emulator. V V
Divider Output DVO By selecting a frequency of the divider output, pulse waves are output. V V
External Interrupt control circuit EXT_INT The port input by switch triggers the generation of the external interrupt. An LED turns on when the external interrupt is detected. V V
Flash Memory FLASH
MCU_BOOTROM
In MCU mode, this sample program applies Security Program and writes test data using a support program (API) provided in the BOOTROM.   V
FLASH
MCU_ProductID
In Product ID mode, this sample program reads the vendor ID, flash ID and security status from the flash memory and displays them on a terminal emulator. V  
FLASH
MCU_RAM
In MCU mode, the control program is transferred to the RAM and writes or reads test data. V V
FLASH
MCU_SHADOW_BOOTROM
(External)
This sample program rewrites a program transferred from an external control board using a support program (API) provided in the BOOTROM and shadow RAM. This sample is for the external control board.   V
FLASH
MCU_SHADOW_BOOTROM
(Sample)
This sample program rewrites a program transferred from an external control board using a support program (API) provided in the BOOTROM and shadow RAM. This sample is for the target board.   V
FLASH
SPROM_UART
The sample program of an external control board writes or reads test data on the target board through UART communication. V V
Key-on Wakeup KWU The NORMAL1 and STOP modes are switched by pushing down a switch, and the LED display is also switched according to the operation mode. V V
LCD LCD The values from 0 to 999 are counted up per second and displayed on the LCD.   V
Operation mode control circuit LOW_POWER
NORMAL1/NORMAL2/SLOW1
The operation mode is changed by a switch input. An LED turns on or blinks according to operation modes. V V
I/O Ports PORT When a switch is pushed down, an LED turns on. When the switch is released, the LED turns off. V V
Real Time Clock RTC An LED repeats turn on/off each interrupt cycle of the real-time clock (RTC). V V
Serial Bus Interface SBI By a command input (via UART) from a terminal emulator of a PC, the sample program executes the following:
1. The Master mode setting
2. Transmission of one byte of test data to the Slave side.
3. Transmission request of the test data to the Slave side.
The Slave side transmits the test data, when it receives the transmission request.
V V
Shadow RAM SHADOW_RAM
COPY
This sample program transfers the shadow RAM copy program to the internal RAM.   V
SHADOW_RAM
POWER_CUT
This sample program turns off/on the power supply of the Flash memory from the shadow RAM   V
Synchronous Serial Interface SIO
8bit_RECEIVE
One byte of test data received from the board in the transmit mode is displayed on a terminal emulator. V V
SIO
8bit_TRANS
One byte of test data is transmitted by the command input (via UART) from a terminal emulator of a PC. V V
SIO
8bit_TRANS_RECEIVE
This sample program uses two evaluation boards that have the program. When one of the boards transmits one byte of test data, the other receives it and displays it on a terminal emulator. V V
Time Base Timer TBT An LED repeats turn on/off each interrupt cycle of the time base timer (TBT). V V
8-bit Timer Counter TC0
8bit_EVENT_COUNT
In the 8-bit event counter mode sample, an LED repeats turn on/off per setting cycle by using the timer interrupt. V V
TC0
8bit_PPG
In the 8-bit programmable pulse generation (PPG) output mode sample, the frequency and duty ratio are changed by a switch input. V V
TC0
8bit_PWM
In the 8-bit pulse width modulation (PWM) output mode sample, the frequency and duty ratio are changed by a switch input. V V
TC0
8bit_TIMER
In the 8-bit timer mode sample, an LED repeats turn on/off each interrupt cycle of the 8-bit timer. V V
TC0
12bit_PWM
In the 12-bit pulse width modulation (PWM) output mode sample, the frequency and duty ratio are changed by a switch input. V V
TC0
16bit_EVENT_COUNT
In the 16-bit event counter mode sample, an LED repeats turn on/off per setting cycle by using the timer interrupt. V V
TC0
16bit_PPG
In the 16-bit programmable pulse generation (PPG) output mode sample, the frequency and duty ratio are changed by a switch input. V V
TC0
16bit_TIMER
In the 16-bit timer mode sample, an LED repeats turn on/off each interrupt cycle of the 16-bit timer. V V
16-bit Timer Counter(TCA) TCA
EVENT_COUNT
In the event counter mode sample, an LED repeats turn on/off each interrupt cycle of the TCA timer. V V
TCA
EXT_TRIG
In the external trigger timer mode sample, an LED repeats turn on/off each interrupt cycle of the TCA timer. V V
TCA
PPG
In the PPG output mode sample, the remote control waveform is output with a 200 msec cycle. V V
TCA
PULSE_WIDTH_MEASURE
In the pulse width measurement mode sample, the measured value of input pulse width is displayed on a terminal emulator. V V
TCA
TIMER
In the timer mode sample, an LED repeats turn on/off each interrupt cycle of the TCA timer. V V
TCA
WINDOWS
In the window mode sample, an LED repeats turn on/off each interrupt cycle of the TCA timer. V V
16-bit Timer Counter(TCB) TCB
PPG
In the PPG output mode sample, the remote control waveform is output with a 200 msec cycle.   V
10-Bit Timer/Counter TCC
PPG_DUTY_50
A waveform whose duty ratio is 50% is output.   V
TCC
PPG_DUTY_CHANGE
A waveform having the specified pulse widths is output.   V
TCC
PPG_DUTY_INDEPENDENT
The waveforms having the specified pulse widths for each of the PPGC01 and PPGC02 pins are output.   V
TCC
PPG_EMG
An LED turns on when an emergency PPG output stop input is accepted. When the emergency PPG output stop state is released, an LED turns off.   V
Asynchronous Serial Interface UART Each character input is echoed to a terminal emulator as it is entered. V V
UART
IrDA
Test data in infrared data format (IrDA) are output with 100 msec cycle. V V
Voltage Detection Circuit VOLT_DETECT Falling of the power supply voltage is detected, and LED patterns corresponding to the detected voltage are set. V V
Watchdog Timer WDT When the clear code is written regularly, all LEDs blink. V V
SP No. Module Name Outline
SP-870-101 - The operational function of the TMP89FS60FG Sample Program
  • 8-bit PWM output
  • 8-bit PPG output
  • 16-bit PPG output
  • UART output
  • SIO output
  • I2C output
  • 10-bit AD input
SP-870-102 RAM, Memory Self-Diagnostic Testing Sample Software

Contacts

Technical inquiry

Contact us

Contact us

Frequently Asked Questions

FAQs
A new window will open