Asia-Pacific
English
简体中文
繁體中文
한국어
日本語
Americas
English
Europe (EMEA)
English



부품 번호 검색

상호 참조 검색

About information presented in this cross reference

The information presented in this cross reference is based on TOSHIBA's selection criteria and should be treated as a suggestion only. Please carefully review the latest versions of all relevant information on the TOSHIBA products, including without limitation data sheets and validate all operating parameters of the TOSHIBA products to ensure that the suggested TOSHIBA products are truly compatible with your design and application.
Please note that this cross reference is based on TOSHIBA's estimate of compatibility with other manufacturers' products, based on other manufacturers' published data, at the time the data was collected.
TOSHIBA is not responsible for any incorrect or incomplete information. Information is subject to change at any time without notice.

키워드 검색

파라미터 검색

재고 확인 및 구매

M4M Group Sample Software

This page provides a sample software download service for the M4M group.

TMPM4MN/4MM/4ML

Please check the target product and function list, and download the appropriate file.

Product Name

Please check the target product.

TMPM4MNFYADFG TMPM4MMFYAFG TMPM4MLFYAUG
TMPM4MNFWADFG  TMPM4MMFWAFG TMPM4MLFWAUG
TMPM4MNFYAFG - TMPM4MLFYAFG
TMPM4MNFWAFG - TMPM4MLFWAFG

(*) If a function other than that of the TMPM4MNFYAFG is to be checked, the CMSIS Core-related files (C startup file and I/O header file) must be changed properly.

Function list

Function list for sample software.

Sample Software/Function Description
Advanced Encoder Input Circuit A_ENC32 The rotation is detected by the rotary encoder in the encoder mode. The LED blink frequency depends on the count value.
Analog/Digital Converter ADC A program that will display the value , which is measured voltage from a potentiometer.
CAN controller CAN Two channels of potentiometer output voltage are measured by ADC, the conversion result value is transmitted and received in the test loopback mode of CAN, and the received data are displayed on terminal software.
Clock/Mode Control CG Switch to the Low Power Consumption Mode (IDLE/STOP1) by the push SW port input as a trigger. Turn on and off the LED depending on the Operation Mode
CRC CRC Communication with CRC code is added between 2 TSPIs and the received data is output to terminal software.
Digital Noise Filter DNF This sample software detects the external interrupt signal that is generated by the switch via the DNF.
Serial Bus Interface El2C/I2C Sample software is communication sample between 2 evaluation boards. And multi master sample software that read EEPROM using 2 evaluation boards.
Flash Control FLASH 1. Example of running a program in the internal RAM and performing delete and rewrite of the internal flash memory
2. Example of rewriting the data flash memory and the user information area of code flash memory
3. Examples of setting the protection function for the page and/or the block of code flash memory
Voltage Detection Circuit LVD This sample software compares the supply voltage with the detection voltage.
Oscillation Frequency Detector OFD This sample software detect error of external high speed oscillator by compare to set frequency width.
I/O port PORT Key presses are determined by polling process to turn on (turn off) the LED.
RAM Parity RAMP Add RAM parity to the character string input using the write command from the terminal software and save it in the RAM. Do a parity check on the data saved in RAM with the Read command and display it to the terminal software.
Clock Selective Watchdog Timer SIWDT Example in which an NMI interrupt occurs and an example in which the clear code is periodically written and an NMI interrupt does not occur
32-bit Timer Event Counter T32A 1. A clock frequency input from outside is measured using the capture function.
2. Example of using the timer interrupt to turn on / off the LED every second
3. Output example of duty-variable PPG (programmable square wave)
Trimming Circuit TRM The frequency of the internal high-speed oscillator is adjusted using an external reference signal..
Serial Peripheral Interface  TSPI It communicates using 2 ch TSPI and outputs data to terminal software.
Asynchronous Serial Communication Circuit
UART 1. Example of receiving the character string from a terminal emulato
2. Example of sending the character string to a terminal emulator

Download

Please check the target product.

Name

문의

기술 문의

문의

문의

자주 있는 문의

자주 있는 문의