Part Number Search

Cross Reference Search

About information presented in this cross reference

The information presented in this cross reference is based on TOSHIBA's selection criteria and should be treated as a suggestion only. Please carefully review the latest versions of all relevant information on the TOSHIBA products, including without limitation data sheets and validate all operating parameters of the TOSHIBA products to ensure that the suggested TOSHIBA products are truly compatible with your design and application.
Please note that this cross reference is based on TOSHIBA's estimate of compatibility with other manufacturers' products, based on other manufacturers' published data, at the time the data was collected.
TOSHIBA is not responsible for any incorrect or incomplete information. Information is subject to change at any time without notice.

Keyword Search

Parametric Search

Stock Check & Purchase

Select Product Categories

TLCS-900/H1 Series Development System

model 15 On-Chip Debug Emulation System

model 15 On-Chip Debug Emulation System

The model 15 On-Chip Debug Emulation System is an old type of the On-Chip Debug Emulation System.
The model 15 On-Chip Debug Emulation System is comprised of the Integrated Development Environment, model 15 controller, On-Chip Debug emulator and accessories.

  • Capable of debugging in the operating condition equivalent to the MCU installed product.
  • Real-time PC/PD trace.
  • Trace control using an event feature.
  • Capable of referring to the memory during program execution.
Host interface Ethernet, RS-232C (25pin straight cable)
Emulation memory Memory on target board
Event Number of points 8 points
Comparison items Address, data, status, external input
Comparison conditionscondition match, unmatch, range
Pass count 1 to 256 times
Event trigger actions Break, trace control, timer control, external trigger output
Event combinations AND, OR, sequential
Hardware break
4 points
Software break 1024 points
Trace memory Capacity 256 frames (Note)
Trace memory Modes free trace, trigger trace, overwriting prohibit, overflow stop
Trace items PC address, data address, data value, status, external output, external input, event
Timer measurement Run timer: 1 channel, Lap timer: 1 channel
Memory access Memory display during program execution 64 bytes
Memory rewrite during program execution -
Program variables Program variables Binary, octal, decimal, or hexadecimal display can be selected for each variable.
Registration Variables, arrays, structures and unions can be registered by the elements.
Sauce display - Source
- Source + assembler code
- Source + assembler code + machine language
External output 1 line
External input 1 line
Performance analysis: Module time measurement -
Performance analysis: Coverage measurement -
Flash programming/security feature External Flash memory can be programmed during debugging.

(Note) There are some cases where the trace memory capacity varies by a tracing condition or operating status.

RTE900/H1 model 15 On-Chip Debug Emulator

Product Configuration and Appearance

Product Configuration and Appearance

BM92CZ26XB0A-M15
BM92CZ26XB0A-M15

Product Configuration and Appearance

  • Host system
  • Ethernet、RS-232C (25pin straight cable)
  • Microcomputer on the target system (with on-chip debug function incorporated)
  • Communication connector
    (Notes) When the On-Chip Debug Emulator is connected to the target system, the communication pins and the monitor pins are used exclusively by the Emulator and cannot be used as port pins.
    (Notes) For the operation assurance range and characteristics of the supplied power/clock, see the microcomputer's datasheet.


Content of Product

BM92CZ26XB0A-M15

  • BM92CZ26XB0A-M15
  • Communication cable (for OCDE)
  • Communication cable (for target)
  • Target connection adapter
  • FG cable
  • Manual

 

About Emulation Operating Voltage/Frequency

Any operating frequency and operating voltage in the device operation assurance range is available.
Note that the power/clock cannot be supplied from the emulator to the target system.

The photo of RTE model 15

RTE model 15

RTE Controller model 15 is a control unit to set up RTE model 15 system. Using RTE Controller model 15 together with an emulation pod and a debugger, enables sophisticated debugging.

Contents of the product package

  • RTE Controller model 15
  • Emulation pod Connection cable 1
  • Emulation pod Connection cable 2
  • Power cable
  • The Integrated Development Environment (IDE):1 download license (from website) (Note)
  • User's manual
    (Note) The Integrated Development Environment does not support TLCS-870/X Series. For the TLCS-870/X Series, purchase theTLCS-870/X Series Debugger.
Power supply AC100V - 240V
Power supply frequency
50Hz - 60Hz
External Dimensions 136(H)*130(W)*320(D)mm
Weight approx. 2.7kg

Accessories

Accessories

A communication cable/communication connector is used for connecting an emulator to a target system.
The communication cable/communication connector is a product made by Samtec,Inc.

Communication cable

Name Part Number
Communication cable
FFSD-10-D-07.00-01-N

Communication Connector

Name Part Number
Communication connector
FTSH-110-01-F-DV-EJ

Contacts

Technical inquiry

Contact us

Contact us

Frequently Asked Questions

FAQs
A new window will open