Part Number Search

Cross Reference Search

About information presented in this cross reference

The information presented in this cross reference is based on TOSHIBA's selection criteria and should be treated as a suggestion only. Please carefully review the latest versions of all relevant information on the TOSHIBA products, including without limitation data sheets and validate all operating parameters of the TOSHIBA products to ensure that the suggested TOSHIBA products are truly compatible with your design and application.
Please note that this cross reference is based on TOSHIBA's estimate of compatibility with other manufacturers' products, based on other manufacturers' published data, at the time the data was collected.
TOSHIBA is not responsible for any incorrect or incomplete information. Information is subject to change at any time without notice.

Keyword Search

Parametric Search

Stock Check & Purchase

Select Product Categories

TXZ4 Series

A sample program is available for each product in the following configuration.

M4K Group(1)

Product Name

TMPM4K4FYAUG TMPM4K2FYADUG TMPM4K1FYAUG TMPM4K0FSADUG
TMPM4K4FYAFG TMPM4K2FWADUG TMPM4K1FWAUG
TMPM4K4FWAUG TMPM4K2FUADUG TMPM4K1FUAUG
TMPM4K4FWAFG TMPM4K2FSADUG TMPM4K1FSAUG
TMPM4K4FUAUG
TMPM4K4FUAFG
TMPM4K4FSAUG
TMPM4K4FSAFG
(*) If a function other than that of the TMPM4K4FYA is to be checked, the CMSIS Core-related files (C startup file and I/O header file) must be changed properly.
Sample Program/Function Description
Analog/Digital converter ADC A program that will display the value , which is measured voltage from a potentiometer.
Clock/Mode control CG Switch to the Low Power Consumption Mode (IDLE/STOP1) by the push SW port input as a trigger. Turn on and off the LED depending on the Operation Mode
CRC CRC Communication with CRC code is added between 2 TSPIs and the received data is output to terminal software.
Digital Noise Filter DNF This sample program is that external interrupt by switch is detected via DNF.
Flash control FLASH Example of running a program in the internal RAM and performing delete and rewrite of the internal flash memory
A sample program that uses code flash as data flash (code flash EEPROM emulation: CFC).
I/O port GPIO Key presses are determined by polling process to turn on (turn off) the LED.
Serial bus interface I2C Sample program is communication sample between 2 evaluation boards. And multi master sample program that read EEPROM using 2 evaluation boards.
Voltage Detection Circuit LVD This sample program compares supply voltage and detection voltage.
Oscillation Frequency Detector OFD This sample program detect error of external high speed oscillator by compare to set frequency width.
RAM Parity RPAR Add RAM parity to the character string input using the write command from the terminal software and save it in the RAM. Do a parity check on the data saved in RAM with the Read command and display it to the terminal software.
32-bit Timer T32A Example of timer interrupt that runs every 1 ms
Output example of duty-variable PPG (programmable square wave).
Trimming Circuit TRM Sample program that is adjusts internal oscillator using reference clock.
Synchronized serial interface TSPI It communicates using 2 ch TSPI and outputs data to terminal software.
Asynchronous Serial Channel UART The data input from the terminal software on PC is echoed back.
UART
DMAC
The data input from the terminal software on PC is echoed back. This sample program use DMAC.

M4K Group(2)

Product Name

TMPM4KQFDFG TMPM4KPFDDFG TMPM4KNFDDFG TMPM4KMFDDFG TMPM4KLFDUG
TMPM4KQFYFG TMPM4KPFYDFG TMPM4KNFYDFG TMPM4KMFYDFG TMPM4KLFYUG
TMPM4KQFWFG TMPM4KPFWDFG TMPM4KNFWDFG TMPM4KMFWDFG TMPM4KLFWUG
TMPM4KNFDFG TMPM4KMFDFG TMPM4KLFDFG
TMPM4KNFYFG TMPM4KMFYFG TMPM4KLFYFG
TMPM4KNFWFG TMPM4KMFWFG TMPM4KLFWFG
(*) If a function other than that of the TMPM4KQFDFG is to be checked, the CMSIS Core-related files (startup file and I/O header file) must be changed properly.
Sample Program/Function Description
Advanced Encoder Input Circuit A_ENC32 The rotation is detected by the rotary encoder in the encoder mode. The LED blink frequency depends on the count value.
Analog/Digital Converter ADC A program that will display the value , which is measured voltage from a potentiometer.
CAN Controller CAN Two channels of potentiometer output voltage are measured by ADC, the conversion result value is transmitted and received in the test loopback mode of CAN, and the received data are displayed on TeraTerm.
Clock/Mode Control CG Switch to the Low Power Consumption Mode (IDLE/STOP1) by the push SW port input as a trigger. Turn on and off the LED depending on the Operation Mode
CRC CRC The data of the amount of "MEMORY_SIZE" are input continuously to the CRC from "MEMORY_TOP". The CRC result is stored in "crc_data".
Digital Noise Filter DNF This sample program detects the external interrupt signal that is generated by the switch via the DNF.
Flash Control FLASH This sample program erases and re-programs data in a specified block in the Flash memory.
Code Flash memory, Data Flash memory, User information area, and others are used.
Serial Bus Interface I2C This sample program communicates between 2 evaluation boards. This is an example of Master-Slave communication.
Voltage Detection Circuit LVD This sample program compares the supply voltage with the detection voltage.
Oscillation Frequency Detector OFD This sample program detect error of external high speed oscillator by compare to set frequency width.
I/O port PORT The detection of push-down of a key turns on (or turns off) the LED.
RAM Parity RAMP Add RAM parity to the character string input using the write command from the terminal software and save it in the RAM. Do a parity check on the data saved in RAM with the Read command and display it to the terminal emulator.
Watchdog Timer with Clock Selection Function
Clock Selective Watchdog Timer
SIWDT An example in which an NMI interrupt occurs and an example in which the clear code is periodically written and an NMI interrupt does not occur
32-bit Timer T32A Example of timer interrupt that runs every 1 ms
Output example of PPG (Programmable Pulse Generator).
Trimming Circuit TRM Sample program that is adjusts internal oscillator using reference clock.
Synchronized Serial Interface TSPI Communication is done using the TSPI. The data are output to the terminal software.
The CRC, the DMA, and the FIFO are used for the communication.
Asynchronous Serial Communication Circuit
Asynchronous Serial Channel
UART The data input from the terminal software on the PC are echoed back.
This sample program includes the program with the DMAC and the program without the DMAC.

M4G Group(1)

Product Name

TMPM4G9F15FG TMPM4G8F15FG TMPM4G7F10FG TMPM4G6F10FG
TMPM4G9F15XBG TMPM4G8F15XBG TMPM4G7FEFG TMPM4G6FEFG
TMPM4G9F10FG TMPM4G8F10FG TMPM4G7FDFG TMPM4G6FDFG
TMPM4G9F10XBG TMPM4G8F10XBG
TMPM4G9FEFG TMPM4G8FEFG
TMPM4G9FEXBG TMPM4G8FEXBG
TMPM4G9FDFG TMPM4G8FDFG
TMPM4G9FDXBG TMPM4G8FDXBG
(*) This sample program operates on the evaluation board of the TMPM4G9F15FG.
If a function other than that of the TMPM4G9F15 is to be checked, the CMSIS Core-related files (C startup file and I/O header file) must be changed properly.
The BSP-related file is dedicated to the evaluation board (TMPM4G9F15). If a function other than that of the TMPM4G9F15 is to be checked, the BSP-related file must be changed properly.
Sample Program/Function Description
Analog/Digital converter ADC

1. The sample program displays the temperature, which is the ADC value measured by the thermistor and converted to temperature by the CPU, on the terminal emulator.

2. Example of displaying the result of the AD monitor function on the LED.

CEC CEC The sample program is a communication sample between 2 evaluation boards.
Clock/Mode control CG Switch to the Low Power Consumption Mode (IDLE/STOP1/STOP2) by the push SW port input as a trigger. Turn on and off the LED depending on the Operation Mode.
Digital/Analog converter DAC This is an example of DAC outputting data input from the terminal emulator.
Digital Noise Filter DNF The sample program detects external interrupt by switch via DNF.
External Bus Interface EBIF Depending on the command (write or read) input on the terminal emulator, stored/read in the SRAM.
Flash control FLASH

1. Example of rewriting the data flash by using Dual mode.

2. Example of rewriting the data in code flash by using User Boot mode.

3. Example of rewriting the user information area of flash.

Full Universal Asynchronous Receiver Transmitter Circuit FUART The data input from the terminal emulator on the PC are echoed back.
FUART/
DMAC
The data input from the terminal emulator on the PC are echoed back. The sample program uses DMAC.
I/O port GPIO Key presses are determined by polling process to turn on (turn off) the LED.
High Speed DMA Controller HDMAC The data input on the terminal emulator are sent to memory by DMA. The data sent to memory are displayed on the PC.
HDMAC/
TSPI
The data input on the terminal emulator are sent from memory to SPI by DMA. The data received via loopback of SPI are displayed on the terminal emulator.
Serial bus interface I2C

Depending on the command (write or read) input on the terminal emulator, stored/read in the I2C EEPROM.

The sample program is a master/slave communication sample between 2 evaluation boards.

Interval Sensor Detection Circuit ISD Detect signal by interval sensor, switch to Normal mode from Stop1 mode of Operation Mode.
Long Term Timer LTTMR This sample program generates 32kHz by LTTMR.
Voltage Detection Circuit LVD This sample program compares supply voltage and detection voltage.
Multi-Function DMA Controller MDMAC The data input from the terminal emulator on the PC are echoed back.
Oscillation Frequency Detector OFD The sample program detects error of external high-speed oscillator by comparing to the set frequency width.
Remote control signal preprocessor RMC The remote controller code is displayed on the terminal emulator.
Real Time Clock RTC The RTC is operated. The clock data are output to the terminal emulator.
Serial Memory Interface SMIF Depending on the command (write or read) input on the terminal emulator, stored/read in the serial Flash.
32-bit Timer T32A Example of timer interrupt that runs every 1 ms
Output example of duty-variable PPG (programmable square wave).
Trimming Circuit TRM The sample program adjusts internal oscillator using reference clock or external low-speed oscillator.
Synchronized serial interface TSPI

1. The sample program communicates using 2 ch TSPI and outputs data to the terminal emulator.

2. Example of controlling the accelerometer on the evaluation board using TSPI function.

Asynchronous Serial Channel UART

1. The data input from the terminal emulator on the PC are echoed back.

2. The sample program communicates using half-clock mode and the received data are displayed on the terminal emulator.

M4L Group(1)

Sample Program/Function Description
Advanced Encoder Input Circuit (32-bit) A_ENC32 The rotation of the rotary encoder is detected in Encoder mode.
12-bit Analog to Digital Converter ADC 2-channel output voltages of the potentiometer are measured by the ADC.
Clock Control/Operation Mode CG Example of switching between Normal mode and Low Power mode
CRC Calculation Circuit CRC The CRC continuously receives the data in the specified region of the memory to calculate their CRC value.
Digital Noise Filter circuit DNF The port input by the switch is detected via DNF, and the external interrupt is generated.
Flash Memory FLASH 1. Examples of erasing in a page unit, erasing in a block unit, programming(write) operation to a code flash, and erasing in an area unit
2. Examples of setting the protection function and protection release
3. Example of rewriting the user information area of flash
4. Example of rewriting the flash data area by using User Boot mode
Voltage Detection Circuit LVD The voltage level is detected. The lighting of LEDs is controlled by the detection result.
Oscillation Frequency Detector OFD The frequency of a target clock (an external high-speed oscillator) is detected. The lighting of LEDs is controlled by the detection result.
Input/Output Port PORT Usage example of Port using LEDs and switches
RAM Parity RAMP The input character string from a terminal emulator is stored to the RAM by the write command. Its parity is also stored. The stored data in the RAM are read, the parity is checked, and the data are displayed on a terminal emulator.
Clock Selective Watchdog Timer SIWDT Example in which an NMI interrupt occurs and an example in which the clear code is periodically written and an NMI interrupt does not occur
32-bit Timer Event Counter T32A 1. A clock frequency input from outside is measured using the capture function.
2. Example of using the timer interrupt to turn on / off the LED every second
3. Output example of duty-variable PPG (programmable square wave)
Trimming Circuit TRM The frequency of the internal high-speed oscillator is adjusted using an external reference signal.
Serial Peripheral Interface TSPI It communicates using TSPI and outputs data to a terminal emulator.
Asynchronous Serial Communication Circuit UART 1. The data received from a terminal emulator are echoed back and output to the terminal emulator through the UART.
2. Example of receiving the character string from a terminal emulator
3. Example of sending the character string to a terminal emulator

Contacts

Technical inquiry

Contact us

Contact us

Frequently Asked Questions

FAQs
A new window will open