Standard Digital Isolators

Toshiba Standard Digital Isolators have low pulse distortion and high CMTI, which are required for isolation of high-speed signaling, and are applicable to a wide range of consumer and industrial applications. In particular, the isolation transformer circuit offers high CMTI by adopting the magnetic coupling method developed by Toshiba.

Lineup

Data transfer rate (Max) (Mbps)
Output Interface
VCC/VDD (Min) (V)
VCC/VDD (Max) (V)
BVS (Min) (Vrms)
Results:

型號需要超過三個文字以上

About information presented in this cross reference

The information presented in this cross reference is based on TOSHIBA's selection criteria and should be treated as a suggestion only. Please carefully review the latest versions of all relevant information on the TOSHIBA products, including without limitation data sheets and validate all operating parameters of the TOSHIBA products to ensure that the suggested TOSHIBA products are truly compatible with your design and application.
Please note that this cross reference is based on TOSHIBA's estimate of compatibility with other manufacturers' products, based on other manufacturers' published data, at the time the data was collected.
TOSHIBA is not responsible for any incorrect or incomplete information. Information is subject to change at any time without notice.

Recommended product

Standard Digital Isolators

Isolated 4 channel logic supporting 150Mbps data rate
For use in industrial control applications like the isolation of bus lines between ICs using different power supply source in different potential, or the suppression of external noise via a data line, Toshiba standard digital isolators transmit at a data rate over 100Mbps higher than photocouplers can achieve.

Standard Digital Isolators

Over 100kV/μs high Common Mode Transient Immunity (CMTI)
Toshiba standard digital isolators utilize their own unique topology of magnetic coupling and shutout common-mode noise to provide a high CMTI.

Standard Digital Isolators

What is the isolation life of the standard digital isolator "DCL54x01"?
Isolation life of the standard digital isolator can be predicted by applying the same concept as MOSFET gate-oxide breakdown over time (TDDB: Time Dependent Dielectric Breakdown [Note 1]).

Standard Digital Isolators

Standard Digital Isolator with Robust Electromagnetic Compatibility (EMC)
At manufacturing sites where automation is progressing, FA equipment such as inverters/servos and PLCs are operating in the same equipment.

Standard Digital Isolators

What is the impulse voltage tolerance of the standard digital isolator "DCL54x01"?
For inverter systems used in industrial applications, indices related to insulation are defined in the International Standard IEC 61800-5-1 "Adjustable speed electrical power drive system – Safety requirements” [Note 1].

Standard Digital Isolators

Pulse Width Distortion (PWD) 3ns (max) corresponds to 150Mbps high-speed communication
Toshiba's standard 4 channel digital isolators improve PWD within 3ns, perform clear eye patterns and offer a maximum data rate corresponding to 150 Mbps what is enabled by high carrier frequency and on-off keying control.

文件

名稱 日期

Technical topics

應用

Inverter/Servo
詳細資料
Uninterruptible Power Supply
詳細資料
Programmable Logic Controller
詳細資料

聯繫我們

技術方面問題

聯絡我們

聯絡我們

常見問題

常見問答

Queries about purchasing, sampling and IC reliability

線上庫存查詢跟購買

型號需要超過三個文字以上

keyword:

Disclaimer for External Link
Through this website you are able to proceed to the website of our distributors ("Third Party Website") which is not under the control of Toshiba Corporation and its subsidiaries and affiliates (collectively "Toshiba"). The Third Party Website is made available to you as a convenience only and you agree to use the Third Party Website at your own risk. The link of the Third Party Website does not necessarily imply a recommendation or an endorsement by Toshiba of the Third Party Website. Please be aware that Toshiba is not responsible for any transaction done through the Third Party Website, and such transactions shall be subject to terms and conditions which may be provided in the Third Party Website.
開啟新視窗